同雪网 SkiChinese.com 北美滑雪论坛

标题: 修边刃的教学 [打印本页]

作者: 土豆想旅行    时间: 2011-2-14 21:35
标题: 修边刃的教学
我完全没看懂 可能是因为我是非器材派


http://www.youtube.com/watch?v=8fGaWzDtMlM

http://www.youtube.com/watch?v=v8Snxx-d_AA&feature=related

http://www.youtube.com/watch?v=GAGZ6R-yOr4&feature=related

作者: kick    时间: 2011-2-14 23:06
沙发         
作者: lupo    时间: 2011-2-15 06:44
好东西!
作者: smellfish    时间: 2011-2-15 15:46
lupo 发表于 2011-2-15 06:44
好东西!

那个角铁好,还是你上次推荐的那个小的可调角度的工具好?

作者: smellfish    时间: 2011-2-15 16:39
回复 lupo 的帖子

最常用的角铁角度是? 还是没有最常用这一说?

作者: espcsg    时间: 2011-2-16 00:53
smellfish 发表于 2011-2-15 16:39
回复 lupo 的帖子

最常用的角铁角度是? 还是没有最常用这一说?

Every ski manufacture has a recommended bevel setting. But more importantly is your personal perference. I set my ski at 2 degree side and 1 degree base. I think the most common settings for recreational skiers are 2 or 3 side and 1 base.

I prefer to use a guide then a multi edge tool. Money wise, those multi-edge tool always include a small file but these small file usually wears a lot faster then a heat treated mill file, but you have to buy a guide which may cost a little more. Also you can 'feel' the cutting action better with  guide since your finger can rest directly on top of the file or stone that you're using. I've been using the Kuu bevel guide, inexpensive, cost only around $40. Of course compare to those expensive guide it has a draw back. The aluminum body is less durable then a solid stainless steel guide. But with proper care it can easily last for a few years.

作者: Phoenixtear    时间: 2011-2-16 00:59
本帖最后由 Phoenixtear 于 2011-2-23 02:32 编辑

就那个桌子上的3个固定器,在AMAZON是卖160,在ski & bikes居然要买299+tax,太黑了点

作者: smellfish    时间: 2011-2-16 09:22
espcsg 发表于 2011-2-16 00:53
Every ski manufacture has a recommended bevel setting. But more importantly is your personal perfe ...

Thank you so much!

作者: Phoenixtear    时间: 2011-2-16 22:44
lupo  去买吧,这个东西买来不合适不喜欢都能退!  发表于 半小时前


买了的话,一次tremblant trip的钱就没了
作者: espcsg    时间: 2011-2-16 23:15
Phoenixtear 发表于 2011-2-16 22:44
买了的话,一次tremblant trip的钱就没了

Build one yourself

toolbenchplans_img_0.jpg (141 KB, 下载次数: 16)

3

3

toolbenchplans_img_1.jpg (203.39 KB, 下载次数: 18)

4

4

toolbenchplans_img_3.jpg (175.03 KB, 下载次数: 16)

5

5

toolbenchplans_img_4.jpg (155.1 KB, 下载次数: 19)

6

6

toolbenchplans_img_5.jpg (155.09 KB, 下载次数: 20)

7

7

toolbenchplans_img_6.jpg (168.58 KB, 下载次数: 14)

8

8

toolbenchplans_img_7.jpg (162.77 KB, 下载次数: 17)

9

9

toolbenchplans_img_8.jpg (207.81 KB, 下载次数: 17)

10

10

toolbenchplans_img_9.jpg (167.99 KB, 下载次数: 15)

11

11

作者: arooga    时间: 2011-2-17 00:06
我觉得这个支架不难做    homedepot买那种固定工具  在夹板子的地方镶上防滑橡胶即可   
我看wayne用木块做了一个  只能把板子平放上面的  不能立起来固定   





欢迎光临 同雪网 SkiChinese.com 北美滑雪论坛 (http://skichinese.com/skichinese/) Powered by Discuz! X3.2